← Back to overview · Advice
Advice
Running Toilet: How to Find and Fix the Cause
Toilet keeps running? Use the colour test to find out in 15 minutes whether the fill valve, float or flush valve is to blame – and when to call a plumber.
Running toilet – what is behind it?
A running toilet wastes water and therefore money, even if you can hardly hear it. Depending on the fault, many litres flow away unused every day.
How do I recognise a running toilet?
Food colouring test:
Put a few drops of food colouring into the cistern. Wait 15 minutes without flushing. If the colour appears in the bowl, the toilet is running.
Noise test:
A quiet hissing or trickling after flushing indicates a problem.
Other signs:
A running toilet is not always noticed straight away. Look out for limescale marks or a fine trickle on the back wall of the bowl, a cistern that briefly refills now and then without being flushed, and a higher water bill. The water meter also gives it away: if it is running although nobody is using water, a running toilet is a common cause.
Common causes
1. Faulty fill valve seal
The fill valve refills the cistern after flushing. If its seal is worn, water overflows.
Symptom: Water runs continuously into the bowl.
2. Faulty float
The float controls the water level in the cistern. If it is faulty, the water rises too high and runs off via the overflow.
Symptom: Water runs through the overflow pipe.
3. Worn flush valve
The flush valve (rubber seal at the bottom of the cistern) no longer seals properly.
Symptom: Water slowly seeps into the bowl.
What you can do yourself
With newer cisterns you can often replace the seals yourself. Spare parts are available at DIY stores.
Important: Before working on the cistern, shut off the water supply at the angle valve or the cistern's shut-off valve. If there is none, use the main stop valve.
Step by step: open and check the cistern
With a cistern that hangs visibly above the toilet, you can check for yourself:
- Close the cistern's shut-off valve, usually on the wall next to the toilet. If there is none, close the main stop valve
- Lift off the lid and put it down safely; ceramic lids are heavy and fragile
- Flush once and watch where the water keeps running while the cistern fills
- If water runs off via the overflow pipe, the water level is too high: adjust the float or the fill valve
- If water seeps past the flush valve, the seal at the bottom is dirty or worn. Often it is enough to wipe off limescale and dirt
With a concealed cistern, only the flush plate is visible. Behind it you can reach the fill valve and flush valve, but the parts vary by manufacturer. If you are unsure here, it is better to leave the work to a professional.
Who pays in a rented flat?
Small repairs needed for ordinary maintenance are borne by the tenant under the law (Art. 259 of the Swiss Code of Obligations (OR), so-called minor maintenance). Cleaning a dirty seal is usually part of this. Anything beyond that is the landlord's responsibility. Where the line is drawn is often set out in the tenancy agreement. If in doubt, ask the property management before you buy parts or call in a professional.
After the repair
Repeat the colour test after a few days to be sure the cistern stays watertight. Many cisterns have two buttons for a small and a large flush. Using the small button where it is enough saves additional water.
When to call a plumber?
- You cannot find the cause
- The cistern is built in (concealed)
- The problem comes back after the repair
Checklist
- Close the angle valve on the supply line to the cistern
- Remove the lid: is the float stuck, is the seal jammed?
- Watch the water in the toilet bowl (is it still running?)
- Note the brand of the cistern
When to call a professional
- If the cistern is built into the wall
- If water is escaping that you cannot stop
- If spare parts are needed
Emergency 24/7: +41 58 510 76 24
Plumbing glossary: Concealed cistern (Unterputz-Spülkasten) · Fill valve (Füllventil)
This page in German: /blog/wc-laeuft-durch
